升降机升降平台升降货梯

After the installation of the lift, the commissioning work should not be ignored升降机安装完成之后的调试工作不可忽视

    一般我们在完成升降机的安装工作之后都是需要进行调试的,在调试的过程中如果出现问题的话可以立即解决,这样就能够避免在正式使用之中出现意外情况,那个时候就难以保证大家的安全了。下面就是一些调试过程中要注意的要求。

    升降机安装好要怎样调试?升降货梯在安装时一定要注意安全,如果升降货梯安装不当容易造成设备故障或事故。下面为大家提出几点升降货梯安装好后的调试要求:

安装前的准备工作:

1、设备到货后,安装工程师需要对现场再次进行确认,进行水平测试。

2、设备运到现场,需清点所有工具和升降货梯设备。

升降机调试注意要点

1、工作前必须穿戴好个人劳动保护用品,特别注意带好安全帽,高空作业必须系好安全带,电工、焊工穿绝缘鞋、并检查所有使用工具。

2、在调试升降机前一定要穿好绝缘鞋、戴好绝缘手套或者站在绝缘垫上,否则禁止施工。

3、在安装时,应首先与现场施工单位负责人取得联系,共同研究双方在现场工作中的安全措施与安全注意事项,共同遵守执行。

4、升降货梯工作时碧玺在每层厅门外,挂有井下有人工作的标牌。

5、在井道工作时,必须采用36v工作照明灯,在轿厢内工作时必须采用12v工具照明灯。

6、工作场所下面不准听人,下脚手架时不准滑下或跳下。

7、在调试中开车人员要配合好调试人员,精神要集中,听从调试人员的指挥。

8、在调试的崇文区与井道作业时,严禁酒后操作、打闹、开玩笑,搞好写作,监护他人安全工作。

9、动用气、电焊时,要遵守气、电焊安全操作规程,注意安全防火。

升降机设备试运转:设备动力电缆接通,开始试机。将设备空载进行升降运动,中间停顿测试控制按钮,查看各按钮是否灵活有效。将设备满载后,再进行升降作业。查看各按钮是否灵活有效。能否正常运行。将设备升到最高点,检测台面与地坑有无接触间隙是否在合理范围。

所以,大家在进行升降机调试工作的时候一定要遵循上面的这些原则,一定不要存在侥幸心理。

Generally, we need to carry out debugging after completing the installation work of the lift. In the process of debugging, if there is any problem, it can be solved immediately, so as to avoid accidents in the official use, and then it is difficult to guarantee everyone’s safety. Here are some things to be aware of during debugging.
How to adjust the elevator after installation? Pay attention to safety when installing the elevator, if the elevator is not installed properly, it is easy to cause equipment failure or accident. The following for everyone to put forward a few elevator after the installation of debugging requirements:
Preparation before installation:
1. After the arrival of the equipment, the installation engineer shall confirm the site again and conduct horizontal test.
2. When the equipment is delivered to the site, all tools and elevator equipment shall be checked.
Attention to the key points of elevator debugging
Before work must wear personal labor protection supplies, pay special attention to wear a good safety helmet, high altitude work must be fastened safety belt, electricians, welders wear insulation shoes, and check all the use of tools.
Before commissioning the lift must wear good insulation shoes, wear good insulation gloves or stand on the insulation mat, otherwise construction is prohibited.
In the installation, should first get in touch with the person in charge of the site construction unit, jointly study the safety measures and safety precautions of both parties in the site work, and comply with the implementation.
The tourmaline is at the door of each floor when the goods elevator is working, and there is a sign of someone working in the mine.
When working in the well, 36v working light must be used, and 12v tool lighting must be used when working in the cage.
Do not listen to people under the workplace. Do not slide or jump off the scaffolding.
During the debugging, the driver should cooperate with the debugging personnel, focus on the spirit and follow the command of the debugging personnel.
During the debugging of chongwen district and Wells, it is strictly forbidden to operate, play, joke, do well in writing and supervise others’ safety work.
When using gas, electric welding, to observe the gas, electric welding safety operation rules, pay attention to safety fire prevention.
Lift equipment test run: the power cable of the equipment is connected and the machine trial starts. Carry out lifting motion of the equipment with no load, and test the control button to check whether each button is flexible and effective. Lift the equipment when it is fully loaded. Check whether the buttons are flexible and effective. Can work properly. Lift the equipment to the highest point and check whether the contact gap between the surface and the pit is within a reasonable range.
Therefore, everyone in the lift debugging work must follow the above principles, must not exist fluke psychology.

 



Prev:
Next:

无觅相关文章插件,快速提升流量

X

Online Chat

hello 您好,欢迎咨询,请问有什么可以帮您?